We offer a complete range of pressure
sensors/transducers for
incorporation into pressure testing or monitoring assemblies; as
well as complete measurement systems using state of the art
mechanical and electronic technology.
TPX
series is a group of transducers to measure absolute and
relative pressure of liquids and gases
including those that are chemically
aggressive. They are particularly
suitable for use in central heating and water pipe
systems. Optionally, they may be equipped with
a heat exchanger, which
makes them suitable
for measuring media with temperaturesup to 150°C.
The following output signals are available:
4-20mA,0-10V,0-5V and 0-20 mA using standard DIN3650 connector. If a
plug-in indicator WWC1000 is added, it will results in LED output
transducer with 4-20mA output signal.
Technical parameters:
▪
Pressure Ranges
0-6, 0-10, 0-16
or 0-25 bar
▪ Power supply
15÷30V DC for outputs
0÷10V
10÷36V DC for outputs 4÷20mA
▪ Output signal
0÷10V, 4÷20mA, (option
0÷20mA)
▪ Allowable overload
4 x range
▪ Basic error
≤ 0,5% of measure
range MR
▪ Pressure connection
M20x1,5 or G1/2"
▪ Casing protection grade
IP 65
▪ Application
heat distribution networks, heat
distribution centers
Pressure
transducer series GPX are designed for
measuring relative (GPXG) and absolute (GPXA) pressure of gases and
liquids including those that are chemicallyaggressive. It is particularly
recommended for applications in underground mining and
above ground installations
insidecoal processing plants
withpresence of
dangerous coal dust. Measuring element of GPX
is piezo resistive silicon sensor separated from measured medium by
steel diaphragm. Electronic board of GPX is protected by silicone
filler and closed in an enclosure made of
stainless steel which ensures IP65
protection. Electrical connector is placed in steel cover protecting
it against weather conditions and mechanical damages. Pressure
transducers series GPX are products within group I category M1,
safety level ia.
NPX
series is a basic and the most popular group of small pressure
transducers with an built in amplifier. These
transducers are used instead of manometers. Power supply for them is
24 VDC and output signals are 4-20mA with standard connector
DIN43650. If a plug-in indicator WWC1000 is
added, it will results in a LED output transducer with 4-20 mA
output signal. It is possible to make NPX transducer with any
voltage output signal within range 0-10V.
Technical parameters:
▪ Measure ranges
within -1 to 1000 bar
▪ Power supply
15÷30V DC for outputs
0÷10V
10÷36V DC for outputs 4÷20mA
▪ Output signal
4÷20mA, 0÷10V, 0÷5V
▪ Allowable overload
4 x range
▪ Basic error
≤ 0,5% of measure
range MR
≤ 0,2% MR
▪ Pressure connection
manometric M20 x 1,5
or G 1/2"
outer diaphgram M20 x 1,5 lub G 1/2"
inner thread. St.B 1/2" or St.B1/4"
NPX series is a group of miniature pressure, underpressure and
absolute pressure transducers, with built-in
amplifier. Diameter of such a transducer at
its widest point is 22mm and it's total length is 110 mm.
It's output signal is 4-20mA or 0-5V, conducted
out through fixed cable. As an option, we
offer 0-5V output signal applicable to work with 12 VDC power supply
source (car installation) .
Technical parameters:
▪ Measure ranges
from
-1 to 200 bar
▪ Power supply
15÷30V DC for outputs 0÷10V i 0÷5V
9÷30V DC for outputs 0÷5V (w opcji)
10÷36V DC for outputs 4÷ 20mA
JPX series is a group
of od small, light (ap. 100g) and chip pressure transducers with
4-20mA or 0-10V output signal. This series is built using entirely
ceramic sensor.
Technical parameters:
▪ Measure ranges
within from -1 to 1000
bar
▪ Power supply
10÷30V DC (output
signal 4÷20mA i 1÷(5) 6V
11,5÷30V DC (output signal 0÷10V
5V DC (output signal 0,5÷4,5 V)
PX series
is a group of can-transducers to measure pressure underpressure and
absolute pressure. This series has a built-in
amplifier converting output voltage from sensor to 4-20mA, 0-20mA or
0-10V (0-5V) output signal, This amplifier makes it possible to
alter measuring range. Power supply
included 24VDC.
Technical parameters:
▪ Measure ranges
0÷6, 0÷10, 0÷16 or
0÷25bar
▪ Measure ranges
within from -1 to 1000
bar
▪ Power supply
15÷36V DC
▪ Output signal
4÷20mA, 0÷20mA,
20÷0mA, 0÷10V
▪ Basic error
≤ 0,5% of measure
range MRP option ≤ 0,2 % MR
▪ Pressure connection
manometric M20 x1,5 orb G1/2"
outer diaphragm M20x1,5 or G1/2"
inner thread St.B1/2" or St.B1/4"
XM is a group of
transducers to measure very small pressure, underpressure and
absolute pressure of mainly air and dry gases (also fumes) within
range +/-1,25mbar to +/- 60mbar . This series is supplied from 5VDC
power source for output signals 0,25V to 4V. Power supply for output
signals 4-20mA or 0-20mA is 19,5V to 36VDC.
PXH series is a group
of transducers designed to measure liquid in closed tanks. Such a
transducer measures the difference of pressure between the tank's
bottom and space over liquid's surface. To fix a transducer it is
necessary to install a flange or thread connection on the tank's
bottom or very close to it on the tank's wall. The second pressure
connection of PXH must be fixed to the tank's upper part which
is always above liquid surface.
Technical parameters:
▪ Measure ranges
0÷6, 0 ÷10, 0÷16 lub 0÷25bar
within -1 to 1000 bar
▪ Power supply
15÷36V DC
▪ Output signal
4÷20mA, 0÷20mA, 20÷0mA, 0÷10V
▪ Basic mistake
≤ 0,5% of measure range MR
option ≤ 0,2% MR
▪ Pressure connection
manometric M20 x1,5 or G1/2"
outer diaphragm M20x1,5 lub G1/2"
inner thread. St.B1/2" or St.B1/4"
PXW series is a group
of transducers equipped in LCD or LED indicator which
make direct readout possible in pressure or
output signal units. Power supply is 24 VDC. Transducers with 4-20mA
output working as current loop don't need additional power supply.
Technical parameters:
▪ Measure ranges
within -1 to 1000 bar
▪ Power supply
19,5÷36V DC
10÷36 DC for outputs 4÷20mA
▪ Output signal
4÷20mA, 0÷20mA, 20÷0mA, 0÷10V,
0÷5V
▪ Basic error
≤ 0,5% of measure range MR
option ≤0,3% MR
▪ Pressure connection
manometric M20 x1,5 or G1/2"
outer diaphragm M20x1,5 lub G1/2"
inner thread St.B1/2" lub St.B1/4"
MC series is a group
of transducers made on base of PC series to measure pressure and
underpressure. This series is equipped with 3,5 digit LCD indicator
and has battery power supply. Readout of measured quantity is done
during 10 seconds after pressing a key. This series may be used in
place of PX, everywhere where higher performance and more precision
readout is needed.
PT seires is a group of pressure and underpressure overpressure
transducers without inbuilt amplifier. IT is DC supplied 4mA and has
max voltage output signal from 80 to 1000mVDC. To obtain standard
output signal 4-20mA, 0-20mA, 0-10V (0-5V) it works with meters
series MPC.
Parametry techniczne:
▪ Measure rangese
within -1 to 1000 bar
▪ Power supply
current about 4mA
▪ output signal
0÷80mV do 0÷1000mV
▪ Allowable overload
4 x range
▪ Basic error
≤ 0,5% of measure range Mr
≤ 0,2% MR (option)
▪ Pressure connection
manometric M20 x 1,5 lub G 1/2"
outer diaphgram M20 x 1,5 lub G 1/2"
inner thread. St.B 1/2" lub St. B1/4"
▪ Electrical connection
cable in length 2m
▪ Application
measurement of gases and liquid
pressure
Go with the industry's best -- for further information and/or
engineering assistance call us at (708) 449-5700, fax us (708) 449-5703, or e-mail us today!
Schlenker Enterprises, Ltd.
P.O. Box 9277
Lombard, IL 60148-9277, USA
708-449-5700 (Phone)
708-449-5703 (Fax)
